We've launched the new forums! Read more here

FS - SteelFiber i110 CW stiff

Status
Not open for further replies.
Schanker

Schanker

Well-known member
Joined
Sep 27, 2011
Messages
4,483
Reaction score
101
Location
Solvang, CA
Handicap
10.5
For sale is a set of eight, 3i-pw, Aerotech Steelfiber 110i CW. They played to standard length in my apex pros. They are taper tip size .355 and can be butt trimmed if you want to shorten them. The grips are iomic but should probably be replaced. The pull lengths are the following.

3i 38"
4i 37.5"
5i 37"
6i 36.5"
7i 36"
8i 35.5"
9i 35"
Pw 34.75"

Asking $160 shipped Conus.

490b259d124684b572e3746289a360b3.jpg

3fb077a7c55db40464398e50817ae751.jpg

0b31e4c0716062ee41c4bbffb590fd3e.jpg

fafa1fa5b95eca38e8105f09bd3b1ffb.jpg
 
Last edited:
Price Drop.
 
FS - SteelFiber i110 CW stiff

This was my first pull of graphite shafts. There was some questions about the integrity of the tips. It looks like the steel wire came off during the pull. Is this common with the steelfibers? Tips all measure more than .350. I would think the epoxy would easily fill the space and it shouldn't really effect the playability.

Any experienced users, your input would be appreciated.

36d41baf429c7f72e8ff3fb55e845886.jpg


6058dbf08ca18f1f323f8b7212258518.jpg
 
Last edited:
FS - SteelFiber i110 CW stiff

Two questions I would ask are:

Did you use a shaft puller?
What was your heat source?

The first because any twisting of the head can damage the tips. The second because excessive heat can as well.

IMO they don't look bad for a first pull, but I may have been a little less ambitious ;)

ETA: 0.003 is less than the thickness of a sheet of paper and probably within production tolerance.
 
JohnSinVA said:
Two questions I would ask are:

Did you use a shaft puller?
What was your heat source?

The first because any twisting of the head can damage the tips. The second because excessive heat can as well.

IMO they don't look bad for a first pull, but I may have been a little less ambitious ;)

ETA: 0.003 is less than the thickness of a sheet of paper and probably within production tolerance.
Click to expand...

I did use a puller, so no twisting. I used a heat gun on the first 2 and it took along time for the epoxy to break loose, so I used a torch on the others. I was careful to not over heat the shaft. I would run the flame up and down the hosel a few times and then try the puller. If that didn't work a little more heat was applied.

Does anyone have SF's that have been pulled, do they look similar?
 
FS - SteelFiber i110 CW stiff

They look ok from the pics but it can be tough to tell sometimes. I and my sore joints are interested. Can you clean up a couple of the tips and get a pic?
 
JohnSinVA said:
They look ok from the pics but it can be tough to tell sometimes. I and my sore joints are interested. Can you clean up a couple of the tips and get a pic?
Click to expand...

Here's a close up pic of the tip. All are similar.

54d08230d8938712fa3fa80fa3e79ee0.jpg
 
Sold. This thread can be locked up.
 
Status
Not open for further replies.
Back
Top