Villn
Member
- Joined
- Apr 11, 2021
- Messages
- 78
- Reaction score
- 53
I don't really consider this a review by the community standards but I wanted to put graphite shafts into my new Vokey SM8 wedges. (52,56,60) So I went with thePaderson Kinetixx regular flex 115g.
I ordered the shafts from Golf Works along with all the other supplies needed to reshaft. The process seemed simple after watching a few McGolf videos.
Before putting in my new shafts I hit all three wedges on GCQuad and my spin rate was as follows. Note these were 3/4 shots as I never full swing my wedges. I have a 48* approach wedge that I use for shots inside 100 yards.
Vokey SM8
52-08F
56-12D
60-10S
Ball used Pro V1
3/4 shot RPM with stock shafts
52 - 6700 rpm average
56 - 7100 rpm average
60 - 7300 rpm average
(Rounded to nearest 50)
3/4 shot RPM with Paderson Kinetixx
52 - 7100 rpm
56 - 7550 rpm
60 - 7700 rpm
(Rounded to nearest 50)
The gains were great but I think feel may have had a lot to do with it.
The swing weights dropped 2 numbers.
52 - D3 to D1
56 - D5 to D3
60 - D5 to D3
The stock shafts had weights installed into the shafts but I dry fit all the new builds before epoxy and didn't feel the need/want to add weight. Now the 52 is the same swing weight as my irons and I feel confident enough to hit it as a full shot club rather than just the normal long 60 yd pitch.
This was my first time building a club and I'd say it turned out great. Also these wedge shafts are nothing short of great especially in the feel department.
I ordered the shafts from Golf Works along with all the other supplies needed to reshaft. The process seemed simple after watching a few McGolf videos.
Before putting in my new shafts I hit all three wedges on GCQuad and my spin rate was as follows. Note these were 3/4 shots as I never full swing my wedges. I have a 48* approach wedge that I use for shots inside 100 yards.
Vokey SM8
52-08F
56-12D
60-10S
Ball used Pro V1
3/4 shot RPM with stock shafts
52 - 6700 rpm average
56 - 7100 rpm average
60 - 7300 rpm average
(Rounded to nearest 50)
3/4 shot RPM with Paderson Kinetixx
52 - 7100 rpm
56 - 7550 rpm
60 - 7700 rpm
(Rounded to nearest 50)
The gains were great but I think feel may have had a lot to do with it.
The swing weights dropped 2 numbers.
52 - D3 to D1
56 - D5 to D3
60 - D5 to D3
The stock shafts had weights installed into the shafts but I dry fit all the new builds before epoxy and didn't feel the need/want to add weight. Now the 52 is the same swing weight as my irons and I feel confident enough to hit it as a full shot club rather than just the normal long 60 yd pitch.
This was my first time building a club and I'd say it turned out great. Also these wedge shafts are nothing short of great especially in the feel department.
Attachments
-
20210428_012306.jpg63.4 KB · Views: 23
-
20210428_111825.jpg57.7 KB · Views: 23
-
IMG_20210428_114545_380.jpg74.5 KB · Views: 26
-
IMG_20210428_114700_490.jpg79.3 KB · Views: 27
-
20210429_083733.jpg71.7 KB · Views: 30
-
IMG_20210429_093609_901.jpg122.8 KB · Views: 28
-
IMG_20210429_093609_935.jpg59.8 KB · Views: 27
Last edited: